AIRGLOBE AIR PULSE VALVES

AIRGLOBE AIR PULSE VALVES


The electro-magnetic pulse diaphragm valve is composed of two gas cells. When the compressed air is connected,it comes into the back gas cell though the orifice. The pressure in the back gas cell pushes the diaphragm closely against the outlet of the valve and the electro-magnetic valve stays in the "closed" condition.
The electrical signals from the pulse jet control device move the armature of the electro-magnetic pulse valve. The air escape of the back gas cell opens and the back gas cell loses pressure quickly, thus the diaphragm moves back and the compressed air blows through the valve outlet.
The electro-magnetic pulse valve comes into the "open" condition.When the electrical signals from the pulse jet control device disappear, the armature of the electro-magnetic pulse valve returns to its original position. The air escape of the back gas cell closes and the pressure in the back gas cell rises, which pushes the diaphragm closely against the valve outlet.
The electro-magnetic valve comes into its "closed" condition again.   


SOLENOID PULSE VALVE AIRGLOBE (PDF 3.7MB)
COMPARISON MECAIR - AIRGLOBE (PDF 3.7MB)



PULSE VALVES WITH THREADED CONNECTION

Electro-magnetic valve (also called diaphragm valve) is the "switch" for compressed air in the dust clean blowing system of the pulse bag filter. Controlled by the output signals of the pulse jet control device, it makes dust clean to the filter bags cell by cell to keep the resistance of the baghouse within the set range and thus guarantee the processing functions and the dust-collecting efficiency of the baghouse.   
DMF-Z electro-magnetic pulse valves is a right-angle valve, with the 90° angle between the inlet and outlet, which is suitable for the installation connection between the gas dome and the baghouse blow tube to provide good air flow and dust clean pulses satisfying the requirements.

DMF-T electro-magnetic pulse valves are the straight in valva, with the 180° angle between the inlet and outlet, which is suitable for the installatin connection between the inlet and gas dome, outlet and the blow tube to provide good air flow and dust clean pulses satisfying the requiments.

AIRGLOBE VALVES
MODEL Z: RIGHT ANGLE    MODEL T: IN/OUT STRAIGHT


Type definition DMF Z / T X S X
Electro-magnetic
Pulse Valve
Z: Right-angle
  T: Straight
Diameter Double
Diaphragms
Temperature Level
(1.2.3)

No.

Type

Diameter

Number of
diaphragm

Outlet orifice
connection

Weight

Inch mm
1 DMF-Z-20 3/4" 20 1 G 3/4 " 0.65kg
2 DMF-Z-25 1" 25 1 G 1" 0.8kg
3 DMF-Z-40S 1 1/2" 40 2 G 1 1/2" 1.4kg
4 DMF-Z-50S 2" 50 2 G 2" 2.4kg
5 DMF-Z-62S 2 1/2" 62 2 G 2 1/2" 3.5kg
6 DMF-Z-76S 3" 76 2 G 3 " 4.3kg
7 DMF-Z-90S 3 1/2" 90 2 G 3 1/2" 5.75kg
8 DMF-Z-102S 4" 102 2 G 4 " 7.3kg
9 DMF-2L-B 3/4" 20 1 27 0.75kg

Working Pressure 0.4 ~0.6Mpa
Working Media Clean air
Voltage 24VDC 110VAC 220V AC    24VAC
Current 0.8A 0.46A 0.23A

Temperature Level

1 2 3
-25°C - 80°C   -25°C - 150°C

-25°C - 230°C

Protection Class IP65*
Relative Humidity of Air <85%
Diaphragm Life One million blows or 3 years

Body ADC12 diecast aluminium
Ferrule 304 stainless steel
Armature 430FR stainless steel
Diaphragm & seals Nitrile
Spring 321 stainless steel
Screws 302 stainless steel


This models are interchangeable to Mecair, Goyen and Asco.
Some examples:

AIRGLOBE DMF-Z-25 is interchangeable to Mecair Goyen VNP-208 and to the old one VEP-208
AIRGLOBE DMF-Z-40 is interchangeable to Mecair Goyen VNP-214 and to the old one VEP-214

Available on stock also the spare parts such as diaphragm and coils compatible to Goyen, Asco and Mecair. 


OTHER AIRGLOBE PRODUCTS:

PULSE VALVES WITH COMPRESSION FITTINGS

PULSE VALVES WITH COMPRESSION FITTINGS


DMF-ZM electro-magnetic pulse valves are the right-angle valve same as series "z" which is suitable for the installation connection between the gas dome and the baghouse blow tube. There are fixed nut at both ends which make it easy to install the valve.

IN LINE PULSE VALVES

IN LINE PULSE VALVES


Model DMF-Y is suitable fot square tank. 

Directing mounted to gas bag, better blowing effect and small loss of air source.
IN LINE VALVES

IN LINE PULSE VALVES


Directing mounted to gas bag, better blowing effect and small loss of air source.

PULSE SIGNAL CONTROLLER

PULSE SIGNAL CONTROLLER


Mcy-64 Pulse Signal Controller is a major control equipment of bag type dust remover dust blowing system. It's output signal directly control solenoid pulse valve. It uses compressed air to blow off the fi ltration bag in sequnce so as to maintain the resistance of the dust remover to a certain range to obtain good performance.
Micro-processor is applied in the pulse singal controller to adjust the interval and width of the pulse to remove the dust timely. It mainly consists of micro-processor circuit,anti-interference circuit,digit display,operating keyboard, electronic swith and power stablizer with high .intellegience and reliability. Material of the casing is transparent engineering plastic and the controller can be mounted either in the control room or on the dust remover.


BUY WITH INTERFLUID ON-LINE CATALOG

Through our on-line Catalogue, you can check availability, product data sheets and prices reserved to you of all the items we sold.
You can:

  • Create offers with complete prices
  • Check availability and terms of purchase
  • Send orders
  • Consider products perfectly interchangeable with the item you're looking for.
  • Select a favourite series of articles that you can easily find or reorder in the next consultations.

The consultation of our products and their availability does not require any registration.
To be able to buy our products and use all the services that INTERFLUID offers to its customers, just register yourself and follow instructions that will be required.

You will be asked to dedicate one minute of your time to get into the world of INTERFLUID!

Items on stock will be sent just one day after your order.

If you have some very urgent inquiry and you want to receive an offer within 24 hours avoiding the registration or you can't find the code you are looking for, just send us your request to our address: info@interfluid.it.





Offer Prompt Request

Company name* Name* Surname*
Telephone Fax E-mail*
 
Message 

* Mandatory fields


Data treatment informative, according to Art. 13 - D.Lgs. n.196/2003
Clicking on "SEND" you declare to have taken note of the data treatment informative and, according to Art. 13 - D.Lgs. n.196/2003, you give your consent to the provided data management, within the purposes and methods listed in the informative.

INTERFLUID SRL tel 0331 797955 - 772410 fax 0331 772425 email info@interfluid.it